Recommended Suppliersmore
2-propylpentanoyl chloride 2936-08-5 MSDS

Section I.Chemical Product and Company Identification
    Chemical Name 2-n-Propyl-n-valeroyl Chloride
    Portland OR
    Synonym        Not available.    
    Chemical Formula        (CH3CH2CH2)2CHCOCl    
    CAS Number        2936-08-5    

Section II.        Composition and Information on Ingredients    
    Chemical Name        CAS Number Percent (%)        TLV/PEL        Toxicology Data    
    2-n-Propyl-n-valeroyl Chloride        2936-08-5        Min. 95.0 (T) Not available.        Not available.    

Section III. Hazards Identification
    Acute Health Effects        Corrosive to skin, eyes, and respiratory system. Liquid or spray mist may produce tissue damage, particularly in mucous    
    membranes of the eyes, mouth and respiratory tract. Skin contact may produce burns. Eye contact can result in corneal
    damage or blindness. Inhalation of the spray mist may produce severe irritation of respiratory tract, characterized by
    coughing, choking, or shortness of breath. Corrosive materials may cause serious injury if ingested.
    Follow safe industrial hygiene practices and always wear proper protective equipment when handling this compound.
    Chronic Health Effects        CARCINOGENIC EFFECTS : Not available.    
    MUTAGENIC EFFECTS : Not available.
    TERATOGENIC EFFECTS : Not available.
    DEVELOPMENTAL TOXICITY: Not available.
    There is no known effect from chronic exposure to this product. Repeated or prolonged exposure to this compound is
    not known to aggravate existing medical conditions.

Section IV.        First Aid Measures    
    Eye Contact
    Check for and remove any contact lenses. DO NOT use an eye ointment. Flush eyes with running water for a minimum
    of 15 minutes, occasionally lifting the upper and lower eyelids. Seek medical attention. Treat symptomatically and
    supportively.
    Skin Contact
    After contact with skin, wash immediately with plenty of water. Gently and thoroughly wash the contaminated skin with
    running water and non-abrasive soap. Be particularly careful to clean folds, crevices, creases and groin. Cover the
    irritated skin with an emollient. Seek medical attention. Treat symptomatically and supportively. Wash any contaminated
    clothing before reusing.
    If the victim is not breathing, perform artificial respiration. Loosen tight clothing such as a collar, tie, belt or waistband. If
    Inhalation
    breathing is difficult, oxygen can be administered. Seek medical attention. Treat symptomatically and supportively.
    Ingestion        DO NOT INDUCE VOMITING. Loosen tight clothing such as a collar, tie, belt or waistband. If the victim is not breathing,    
    perform mouth-to-mouth resuscitation. Examine the lips and mouth to ascertain whether the tissues are damaged, a
    possible indication that the toxic material was ingested; the absence of such signs, however, is not conclusive.

Section V.        Fire and Explosion Data    
    Not available.
    Auto-Ignition
    Flammability        May be combustible at high temperature.    
    Flammable Limits
    Flash Points        Not available.    
    Not available.
    Combustion Products        These products are toxic carbon oxides (CO, CO 2).    
    Fire Hazards
    No specific information is available regarding the flammability of this compound in the presence of various materials.
    Explosion Hazards        Risks of explosion of the product in presence of mechanical impact: Not available.    
    Risks of explosion of the product in presence of static discharge: Not available.
    No additional information is available regarding the risks of explosion.
    Fire Fighting Media
    SMALL FIRE: Use DRY chemicals, CO 2, water spray or foam.
    LARGE FIRE: Use water spray, fog or foam. DO NOT use water jet.
    and Instructions
    Consult with local fire authorities before attempting large scale fire-fighting operations.
    Continued on Next Page
    2936-08-5rNINGS(International)

Section VI.        Accidental Release Measures    
    Spill Cleanup        Corrosive material.    
    Instructions        In case of a spill and/or a leak, always shut off any sources of ignition, ventilate the area, and exercise caution. Use a    
    shovel to put the material into a convenient waste disposal container. Prevent entry into sewers, basements or confined
    areas; dike if needed. Consult federal, state, and/or local authorities for assistance on disposal.

Section VII. Handling and Storage
    Handling and Storage        CORROSIVE. Keep away from heat and sources of ignition. Mechanical exhaust required. When not in use, tightly seal    
    the container and store in a dry, cool place. Avoid excessive heat and light. DO NOT ingest. DO NOT breathe dust. In
    Information
    case of insufficient ventilation, wear suitable respiratory equipment. If ingested, seek medical advice immediately and
    show the container or the label. Treat symptomatically and supportively. Avoid contact with skin and eyes.
    Always store away from incompatible compounds such as oxidizing agents.

Section VIII. Exposure Controls/Personal Protection
    Engineering Controls        Use process enclosures, local exhaust ventilation, or other engineering controls to keep airborne levels below    
    recommended exposure limits. If user operations generate dust, fume or mist, use ventilation to keep exposure to
    airborne contaminants below the exposure limit.
    Personal Protection        Face shield. Lab coat. Dust respirator. Boots. Gloves. A MSHA/NIOSH approved respirator must be used to avoid    
    inhalation of the product. Suggested protective clothing might not be sufficient; consult a specialist BEFORE handling
    this product.
    Exposure Limits        Not available.    

Section IX. Physical and Chemical Properties
    Solubility
    Physical state @ 20°C        Solid.        Not available.    
    Not available.
    Specific Gravity
    Molecular Weight        162.66        Partition Coefficient        Not available.    
    Boiling Point        Not available.        Vapor Pressure        Not available.    
    Melting Point        144 to 147°C (291.2 to 296.6°F)        Vapor Density        Not available.    
    Not available.        Volatility        Not available.    
    Refractive Index
    Critical Temperature        Odor        Not available.    
    Not available.
    Viscosity        Not available.        Taste        Not available.    

Section X.        Stability and Reactivity Data    
    Stability    
This material is stable if stored under proper conditions. (See Section VII for instructions)    
    Conditions of Instability
    Avoid excessive heat and light.
    Incompatibilities
    Reactive with oxidizing agents.

Section XI. Toxicological Information
    RTECS Number        Not available.    
    Routes of Exposure        Eye contact. Ingestion. Inhalation. Skin contact.    
    Not available.
    Toxicity Data
    Chronic Toxic Effects        CARCINOGENIC EFFECTS : Not available.    
    MUTAGENIC EFFECTS : Not available.
    TERATOGENIC EFFECTS : Not available.
    DEVELOPMENTAL TOXICITY: Not available.
    There is no known effect from chronic exposure to this product. Repeated or prolonged exposure to this compound is not
    known to aggravate existing medical conditions.
    Acute Toxic Effects        Corrosive to skin, eyes, and respiratory system. Liquid or spray mist may produce tissue damage, particularly in mucous    
    membranes of the eyes, mouth and respiratory tract. Skin contact may produce burns. Eye contact can result in corneal
    damage or blindness. Inhalation of the spray mist may produce severe irritation of respiratory tract, characterized by
    coughing, choking, or shortness of breath. Corrosive materials may cause serious injury if ingested.
    Follow safe industrial hygiene practices and always wear proper protective equipment when handling this compound.
    Continued on Next Page
    2-n-Propyl-n-valeroyl Chloride

Section XII.        Ecological Information    
    Ecotoxicity        Not available.    
    Environmental Fate        Not available.    

Section XIII. Disposal Considerations
    Recycle to process, if possible. Consult your local or regional authorities. You may be able to dissolve or mix material with
    Waste Disposal
    a combustible solvent and burn in a chemical incinerator equipped with an afterburner and scrubber system. Observe all
    federal, state, and local regulations when disposing of this substance.

Section XIV. Transport Information
    DOT Classification        CLASS 8: Corrosive material.    
    PIN Number
    Proper Shipping Name
    Corrosive liquid, acidic, organic, n.o.s.
    Packing Group (PG)        III    
    DOT Pictograms

Section XV. Other Regulatory Information and Pictograms
    TSCA Chemical Inventory        This compound is ON the EPA Toxic Substances Control Act (TSCA) inventory list.    
    (EPA)
    WHMIS Classification
    Not available.
    (Canada)
    EINECS Number (EEC) 211-581-7
    EEC Risk Statements        R34- Causes burns.    


SECTION 16 - ADDITIONAL INFORMATION
N/A

Home   |   Announcement   |   Partners   |   Business Cooperation   |   Suppliers   |   Products    |   About Us   |   Contact Us   |   Privacy Policy   |   Terms & Conditions   |   Legal Statement

Copyright © 2013-2016 MOLBASE All Rights Reserved ICP Shanghai 14014220