Recommended Suppliersmore
BIS(DIMETHYLAMINO)PHOSPHORYL CHLORIDE 1605-65-8 MSDS
Name: Bis(Dimethylamino)Phosphorochloridate Tech. 90% Material Safety Data Sheet
Synonym: Tetramethylphosphorodiamidic Chlorid
CAS: 1605-65-8
Section 1 - Chemical Product   MSDS Name:Bis(Dimethylamino)Phosphorochloridate Tech. 90% Material Safety Data Sheet
Synonym:Tetramethylphosphorodiamidic Chlorid

Section 2 - COMPOSITION, INFORMATION ON INGREDIENTS
CAS# Chemical Name content EINECS#
1605-65-8 Bis(Dimethylamino)Phosphorochloridate 90 216-517-1
Hazard Symbols: C
Risk Phrases: 34

Section 3 - HAZARDS IDENTIFICATION
  EMERGENCY OVERVIEW
Causes burns.Corrosive.Moisture sensitive.The toxicological properties of this material have not been fully investigated.
Potential Health Effects
Eye:
Causes eye burns.
Skin:
Causes skin burns.
Ingestion:
May cause severe and permanent damage to the digestive tract. Causes gastrointestinal tract burns. The toxicological properties of this substance have not been fully investigated.
Inhalation:
Causes chemical burns to the respiratory tract. The toxicological properties of this substance have not been fully investigated.
Chronic:
No information found.

Section 4 - FIRST AID MEASURES
  Eyes: Get medical aid immediately. Do NOT allow victim to rub eyes or keep eyes closed. Extensive irrigation with water is required (at least 30 minutes).
Skin:
Get medical aid. Immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes.
Wash clothing before reuse. Destroy contaminated shoes.
Ingestion:
Do not induce vomiting. If victim is conscious and alert, give 2-4 cupfuls of milk or water. Never give anything by mouth to an unconscious person. Get medical aid immediately.
Inhalation:
Remove from exposure and move to fresh air immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical aid. Do NOT use mouth-to-mouth resuscitation.
Notes to Physician:

Section 5 - FIRE FIGHTING MEASURES
  General Information:
As in any fire, wear a self-contained breathing apparatus in pressure-demand, MSHA/NIOSH (approved or equivalent), and full protective gear. During a fire, irritating and highly toxic gases may be generated by thermal decomposition or combustion. Use water spray to keep fire-exposed containers cool. Vapors may be heavier than air. They can spread along the ground and collect in low or confined areas. Containers may explode when heated.
Extinguishing Media:
Use agent most appropriate to extinguish fire. Do NOT get water inside containers. Cool containers with flooding quantities of water until well after fire is out. Use water spray, dry chemical, carbon dioxide, or appropriate foam.

Section 6 - ACCIDENTAL RELEASE MEASURES
  General Information: Use proper personal protective equipment as indicated in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth), then place in suitable container. Avoid runoff into storm sewers and ditches which lead to waterways. Clean up spills immediately, observing precautions in the Protective Equipment section. Remove all sources of ignition. Provide ventilation. Do not get water inside containers.

Section 7 - HANDLING and STORAGE
  Handling:
Wash thoroughly after handling. Use with adequate ventilation. Avoid contact with eyes, skin, and clothing. Keep container tightly closed.
Avoid ingestion and inhalation. Discard contaminated shoes. Keep from contact with moist air and steam.
Storage:
Keep container closed when not in use. Store in a tightly closed container. Store in a cool, dry, well-ventilated area away from incompatible substances. Corrosives area. Store protected from moisture.

Section 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION
  Engineering Controls:
Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower. Use adequate ventilation to keep airborne concentrations low.
Exposure Limits CAS# 1605-65-8: Personal Protective Equipment Eyes: Wear appropriate protective eyeglasses or chemical safety goggles as described by OSHA's eye and face protection regulations in 29 CFR 1910.133 or European Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin exposure.
Clothing:
Wear appropriate protective clothing to prevent skin exposure.
Respirators:
Follow the OSHA respirator regulations found in 29 CFR 1910.134 or European Standard EN 149. Use a NIOSH/MSHA or European Standard EN 149 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced.

Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
 
Physical State: Liquid
Color: clear, colorless
Odor: Not available.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: 246-247C
Freezing/Melting Point: Not available.
Autoignition Temperature: Not available.
Flash Point: > 112 deg C (> 233.60 deg F)
Explosion Limits, lower: N/A
Explosion Limits, upper: N/A
Decomposition Temperature:
Solubility in water:
Specific Gravity/Density: 1.1520
Molecular Formula: C4H12ClN2OP
Molecular Weight: 170.5236

Section 10 - STABILITY AND REACTIVITY
  Chemical Stability:
Stable at room temperature in closed containers under normal storage and handling conditions.
Conditions to Avoid:
Incompatible materials, moisture, excess heat, oxidizers.
Incompatibilities with Other Materials:
Oxidizing agents.
Hazardous Decomposition Products:
Chlorine, nitrogen oxides, carbon monoxide, oxides of phosphorus, irritating and toxic fumes and gases, carbon dioxide.
Hazardous Polymerization: Has not been reported

Section 11 - TOXICOLOGICAL INFORMATION
  RTECS#:
CAS# 1605-65-8 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
Bis(Dimethylamino)Phosphorochloridate - Not listed by ACGIH, IARC, or NTP.

Section 12 - ECOLOGICAL INFORMATION
 

Section 13 - DISPOSAL CONSIDERATIONS
  Dispose of in a manner consistent with federal, state, and local regulations.

Section 14 - TRANSPORT INFORMATION
 
IATA
Shipping Name: CORROSIVE LIQUID, TOXIC, N.O.S.*
Hazard Class: 8 (6.1)
UN Number: 2922
Packing Group: II
IMO
Shipping Name: CORROSIVE LIQUID, TOXIC, N.O.S.
Hazard Class: 8 (6.1)
UN Number: 2922
Packing Group: II
RID/ADR
Shipping Name: CORROSIVE LIQUID, TOXIC, N.O.S.
Hazard Class: 8
UN Number: 2922
Packing group: II

Section 15 - REGULATORY INFORMATION
 
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: C
Risk Phrases:
R 34 Causes burns.
Safety Phrases:
S 28A After contact with skin, wash immediately with
plenty of water.
S 37 Wear suitable gloves.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 1605-65-8: No information available.
Canada
None of the chemicals in this product are listed on the DSL/NDSL list.
CAS# 1605-65-8 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 1605-65-8 is not listed on the TSCA inventory.
It is for research and development use only.


SECTION 16 - ADDITIONAL INFORMATION
N/A

Home   |   Announcement   |   Partners   |   Business Cooperation   |   Suppliers   |   Products    |   About Us   |   Contact Us   |   Privacy Policy   |   Terms & Conditions   |   Legal Statement

Copyright © 2013-2016 MOLBASE All Rights Reserved ICP Shanghai 14014220