Recommended Suppliersmore
Diphosphoryl chloride 13498-14-1 MSDS

  Product identifiers
    Product name        : Diphosphoryl chloride    
    CAS-No.        : 13498-14-1    
  Relevant identified uses of the substance or mixture and uses advised against
    Identified uses        : Laboratory chemicals, Manufacture of substances    

  Classification of the substance or mixture
  Classification according to Regulation (EC) No 1272/2008 [EU-GHS/CLP]
    Skin corrosion (Category 1B)
  Classification according to EU Directives 67/548/EEC or 1999/45/EC
    Reacts violently with water. Causes burns.
  Label elements
  Labelling according Regulation (EC) No 1272/2008 [CLP]
    Signal word        Danger    
    Hazard statement(s)
    H314        Causes severe skin burns and eye damage.    
    Precautionary statement(s)
    P280        Wear protective gloves/ protective clothing/ eye protection/ face    
    P305 + P351 + P338        IF IN EYES: Rinse cautiously with water for several minutes. Remove    
    contact lenses, if present and easy to do. Continue rinsing.
    P310        Immediately call a POISON CENTER or doctor/ physician.    
    Supplemental Hazard information (EU)
    EUH014        Reacts violently with water.    
  According to European Directive 67/548/EEC as amended.
    Hazard symbol(s)
    R14        Reacts violently with water.    
    R34        Causes burns.    
    S26        In case of contact with eyes, rinse immediately with plenty of water and    
    seek medical advice.
    S36/37/39        Wear suitable protective clothing, gloves and eye/face protection.    
    S45        In case of accident or if you feel unwell, seek medical advice immediately    
    (show the label where possible).
  Other hazards - none

    Synonyms        : Pyrophosphoric tetrachloride    
    Diphosphoric tetrachloride
    Pyrophosphoryl chloride
    Formula        : Cl4O3P2    
    Molecular Weight        : 251,76 g/mol    
    Component        Concentration    
  Diphosphoryl tetrachloride
    CAS-No.        13498-14-1        -    
    EC-No.        236-824-4    

  Description of first aid measures
  General advice
    Consult a physician. Show this safety data sheet to the doctor in attendance.
  If inhaled
    If breathed in, move person into fresh air. If not breathing, give artificial respiration. Consult a physician.
  In case of skin contact
    Take off contaminated clothing and shoes immediately. Wash off with soap and plenty of water. Consult a
  In case of eye contact
    Rinse thoroughly with plenty of water for at least 15 minutes and consult a physician.
  If swallowed
    Do NOT induce vomiting. Never give anything by mouth to an unconscious person. Rinse mouth with
    water. Consult a physician.
  Most important symptoms and effects, both acute and delayed
    Material is extremely destructive to tissue of the mucous membranes and upper respiratory tract, eyes, and
    skin., spasm, inflammation and edema of the larynx, spasm, inflammation and edema of the bronchi,
    pneumonitis, pulmonary edema, burning sensation, Cough, wheezing, laryngitis, Shortness of breath,
    Headache, Nausea, Vomiting, To the best of our knowledge, the chemical, physical, and toxicological
    properties have not been thoroughly investigated.
  Indication of any immediate medical attention and special treatment needed
    no data available

  Extinguishing media
  Suitable extinguishing media
    Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
    Dry powder
  Special hazards arising from the substance or mixture
    Nature of decomposition products not known.
  Advice for firefighters
    Wear self contained breathing apparatus for fire fighting if necessary.
  Further information
    The product itself does not burn.

  Personal precautions, protective equipment and emergency procedures
    Use personal protective equipment. Avoid breathing vapors, mist or gas. Ensure adequate ventilation.
    Evacuate personnel to safe areas.
  Environmental precautions
    Do not let product enter drains.
  Methods and materials for containment and cleaning up
    Soak up with inert absorbent material and dispose of as hazardous waste. Do not flush with water. Keep
    in suitable, closed containers for disposal.
  Reference to other sections
    For disposal see section 13.

  Precautions for safe handling
    Avoid inhalation of vapour or mist.
  Conditions for safe storage, including any incompatibilities
    Store in cool place. Keep container tightly closed in a dry and well-ventilated place. Containers which are
    opened must be carefully resealed and kept upright to prevent leakage.
    Never allow product to get in contact with water during storage.
  Specific end uses
    no data available

  Control parameters
  Components with workplace control parameters
  Exposure controls
  Appropriate engineering controls
    Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and
    at the end of workday.
  Personal protective equipment
  Eye/face protection
    Tightly fitting safety goggles. Faceshield (8-inch minimum). Use equipment for eye protection
    tested and approved under appropriate government standards such as NIOSH (US) or EN
  Skin protection
    Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique
    (without touching glove's outer surface) to avoid skin contact with this product. Dispose of
    contaminated gloves after use in accordance with applicable laws and good laboratory practices.
    Wash and dry hands.
    The selected protective gloves have to satisfy the specifications of EU Directive 89/686/EEC and
    the standard EN 374 derived from it.
  Body Protection
    Complete suit protecting against chemicals, Flame retardant protective clothing, The type of
    protective equipment must be selected according to the concentration and amount of the
    dangerous substance at the specific workplace.
  Respiratory protection
    Where risk assessment shows air-purifying respirators are appropriate use a full-face respirator
    with multi-purpose combination (US) or type ABEK (EN 14387) respirator cartridges as a backup
    to engineering controls. If the respirator is the sole means of protection, use a full-face supplied air
    respirator. Use respirators and components tested and approved under appropriate government
    standards such as NIOSH (US) or CEN (EU).

  Information on basic physical and chemical properties
    a) Appearance        Form: clear, liquid    
    Colour: colourless
    b) Odour        no data available    
    c) Odour Threshold        no data available    
    d) pH        no data available    
    e) Melting point/freezing        no data available    
    f) Initial boiling point and 90 °C at 16 hPa - lit.
    boiling range
    g) Flash point        not applicable    
    h) Evaporation rate        no data available    
    i) Flammability (solid, gas) no data available
    j) Upper/lower        no data available    
    flammability or
    explosive limits
    k) Vapour pressure        no data available    
    l) Vapour density        no data available    
    m) Relative density        1,82 g/mL at 25 °C    
    n) Water solubility        no data available    
    o) Partition coefficient: n- no data available
    p) Autoignition        no data available    
    q) Decomposition        no data available    
    r) Viscosity        no data available    
    s) Explosive properties        no data available    
    t) Oxidizing properties        no data available    
  Other safety information
    no data available

    no data available
  Chemical stability
    no data available
  Possibility of hazardous reactions
    Reacts violently with water.
  Conditions to avoid
    Exposure to moisture.
  Incompatible materials
  Hazardous decomposition products
    Other decomposition products - no data available

  Information on toxicological effects
  Acute toxicity
    no data available
  Skin corrosion/irritation
    no data available
  Serious eye damage/eye irritation
    no data available
  Respiratory or skin sensitization
    no data available
  Germ cell mutagenicity
    no data available
    IARC:        No component of this product present at levels greater than or equal to 0.1% is identified as    
    probable, possible or confirmed human carcinogen by IARC.
  Reproductive toxicity
    no data available
  Specific target organ toxicity - single exposure
    no data available
  Specific target organ toxicity - repeated exposure
    no data available
  Aspiration hazard
    no data available
  Potential health effects
    May be harmful if inhaled. Material is extremely destructive to the tissue of
    the mucous membranes and upper respiratory tract.
  Ingestion        May be harmful if swallowed. Causes burns.    
  Skin        May be harmful if absorbed through skin. Causes skin burns.    
    Causes eye burns.
  Signs and Symptoms of Exposure
    Material is extremely destructive to tissue of the mucous membranes and upper respiratory tract, eyes, and
    skin., spasm, inflammation and edema of the larynx, spasm, inflammation and edema of the bronchi,
    pneumonitis, pulmonary edema, burning sensation, Cough, wheezing, laryngitis, Shortness of breath,
    Headache, Nausea, Vomiting, To the best of our knowledge, the chemical, physical, and toxicological
    properties have not been thoroughly investigated.
  Additional Information
    RTECS: Not available

    no data available
  Persistence and degradability
    no data available
  Bioaccumulative potential
    no data available
  Mobility in soil
    no data available
  Results of PBT and vPvB assessment
    no data available
  Other adverse effects
    no data available

  Waste treatment methods
    Offer surplus and non-recyclable solutions to a licensed disposal company.
  Contaminated packaging
    Dispose of as unused product.

  UN number
    ADR/RID: 3264        IMDG: 3264        IATA: 3264    
  UN proper shipping name
    ADR/RID: CORROSIVE LIQUID, ACIDIC, INORGANIC, N.O.S. (Diphosphoryl tetrachloride)
    IMDG: CORROSIVE LIQUID, ACIDIC, INORGANIC, N.O.S. (Diphosphoryl tetrachloride)
    IATA:        Corrosive liquid, acidic, inorganic, n.o.s. (Diphosphoryl tetrachloride)    
  Transport hazard class(es)
    ADR/RID: 8        IMDG: 8        IATA: 8    
  Packaging group
    ADR/RID: II        IMDG: II        IATA: II    
  Environmental hazards
    ADR/RID: no        IMDG Marine pollutant: no        IATA: no    
  Special precautions for user
    no data available

    This safety datasheet complies with the requirements of Regulation (EC) No. 1907/2006.
  Safety, health and environmental regulations/legislation specific for the substance or mixture
    no data available
  Chemical Safety Assessment
    no data available

  Further information
    Copyright 2012 Co. LLC. License granted to make unlimited paper copies for internal use
    The above information is believed to be correct but does not purport to be all inclusive and shall be
    used only as a guide. The information in this document is based on the present state of our knowledge
    and is applicable to the product with regard to appropriate safety precautions. It does not represent any
    guarantee of the properties of the product. Corporation and its Affiliates shall not be held
    liable for any damage resulting from handling or from contact with the above product. See
     and/or the reverse side of invoice or packing slip for additional terms and conditions of sale.

Home   |   Announcement   |   Partners   |   Business Cooperation   |   Suppliers   |   Products    |   About Us   |   Contact Us   |   Privacy Policy   |   Terms & Conditions   |   Legal Statement

Copyright © 2013-2016 MOLBASE All Rights Reserved ICP Shanghai 14014220