Recommended Suppliersmore
Allylpalladium chloride dimer 12012-95-2 MSDS
Name: Allylpalladium chloride dimer 98% Material Safety Data Sheet
Synonym: Allyl palladium chloride dime
CAS: 12012-95-2
Section 1 - Chemical Product   MSDS Name:Allylpalladium chloride dimer 98% Material Safety Data Sheet
Synonym:Allyl palladium chloride dime

Section 2 - COMPOSITION, INFORMATION ON INGREDIENTS
CAS# Chemical Name content EINECS#
12012-95-2 Allylpalladium chloride dimer 98 234-579-8
Hazard Symbols: XI
Risk Phrases: 36/38

Section 3 - HAZARDS IDENTIFICATION
  EMERGENCY OVERVIEW
Irritating to eyes and skin.Air sensitive.Moisture sensitive.
Potential Health Effects
Eye:
Causes eye irritation. May cause chemical conjunctivitis.
Skin:
Causes severe skin irritation.
Ingestion:
May cause gastrointestinal irritation with nausea, vomiting and diarrhea.
Inhalation:
Causes respiratory tract irritation. May cause burning sensation, coughing, wheezing, laryngitis, shortness of breath, headache, nausea, and vomiting. Can produce delayed pulmonary edema.
Chronic:
Effects may be delayed.

Section 4 - FIRST AID MEASURES
  Eyes: Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Get medical aid.
Skin:
Get medical aid immediately. Immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash clothing before reuse.
Ingestion:
Never give anything by mouth to an unconscious person. Get medical aid. Do NOT induce vomiting. If conscious and alert, rinse mouth and drink 2-4 cupfuls of milk or water.
Inhalation:
Remove from exposure and move to fresh air immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical aid.
Notes to Physician:
Treat symptomatically and supportively.

Section 5 - FIRE FIGHTING MEASURES
  General Information:
As in any fire, wear a self-contained breathing apparatus in pressure-demand, MSHA/NIOSH (approved or equivalent), and full protective gear. During a fire, irritating and highly toxic gases may be generated by thermal decomposition or combustion.
Extinguishing Media:
Do NOT get water inside containers. Use water spray, dry chemical, carbon dioxide, or appropriate foam.

Section 6 - ACCIDENTAL RELEASE MEASURES
  General Information: Use proper personal protective equipment as indicated in Section 8.
Spills/Leaks:
Clean up spills immediately, observing precautions in the Protective Equipment section. Sweep up, then place into a suitable container for disposal. Provide ventilation. Place under an inert atmosphere. Do not get water inside containers.

Section 7 - HANDLING and STORAGE
  Handling:
Wash thoroughly after handling. Remove contaminated clothing and wash before reuse. Do not get in eyes, on skin, or on clothing. Keep container tightly closed. Use with adequate ventilation. Handle under an inert atmosphere. Store protected from air. Do not allow contact with water. Use only in a chemical fume hood. Keep from contact with moist air and steam. Do not breathe dust.
Storage:
Store in a tightly closed container. Store in a cool, dry, well-ventilated area away from incompatible substances. Do not expose to air. Store protected from moisture. Store under an inert atmosphere.

Section 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION
  Engineering Controls:
Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower. Use adequate ventilation to keep airborne concentrations low.
Exposure Limits CAS# 12012-95-2: Personal Protective Equipment Eyes: Wear appropriate protective eyeglasses or chemical safety goggles as described by OSHA's eye and face protection regulations in 29 CFR 1910.133 or European Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin exposure.
Clothing:
Wear appropriate protective clothing to prevent skin exposure.
Respirators:
A respiratory protection program that meets OSHA's 29 CFR 1910.134 and ANSI Z88.2 requirements or European Standard EN 149 must be followed whenever workplace conditions warrant respirator use.

Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
 
Physical State: Crystalline powder
Color: yellow
Odor: None reported.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: Not available.
Freezing/Melting Point: 160 deg C
Autoignition Temperature: Not applicable.
Flash Point: Not applicable.
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature: Not available.
Solubility in water: decomposes
Specific Gravity/Density: Not available.
Molecular Formula: C6H10Cl2Pd2
Molecular Weight: 365.84

Section 10 - STABILITY AND REACTIVITY
  Chemical Stability:
Stable at room temperature in closed containers under normal storage and handling conditions. May decompose on exposure to moist air or water.
Conditions to Avoid:
Incompatible materials, moisture, exposure to air, excess heat, strong oxidants.
Incompatibilities with Other Materials:
Strong oxidizing agents, moisture, air.
Hazardous Decomposition Products:
Hydrogen chloride, carbon monoxide, carbon dioxide, chloride fumes.
Hazardous Polymerization: Has not been reported.

Section 11 - TOXICOLOGICAL INFORMATION
  RTECS#:
CAS# 12012-95-2: RT3510000 LD50/LC50:
CAS# 12012-95-2: Draize test, rabbit, skin: 100 mg/24H Severe.
Carcinogenicity:
Allylpalladium chloride dimer - Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.

Section 12 - ECOLOGICAL INFORMATION
  Other No information available.

Section 13 - DISPOSAL CONSIDERATIONS
  Dispose of in a manner consistent with federal, state, and local regulations.

Section 14 - TRANSPORT INFORMATION
 
IATA
Not regulated as a hazardous material.
IMO
Not regulated as a hazardous material.
RID/ADR
Not regulated as a hazardous material.

Section 15 - REGULATORY INFORMATION
 
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: XI
Risk Phrases:
R 36/38 Irritating to eyes and skin.
Safety Phrases:
S 24/25 Avoid contact with skin and eyes.
WGK (Water Danger/Protection)
CAS# 12012-95-2: 0
Canada
None of the chemicals in this product are listed on the DSL/NDSL list.
CAS# 12012-95-2 is listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 12012-95-2 is not listed on the TSCA inventory.
It is for research and development use only.


SECTION 16 - ADDITIONAL INFORMATION
N/A

Home   |   Announcement   |   Partners   |   Business Cooperation   |   Suppliers   |   Products    |   About Us   |   Contact Us   |   Privacy Policy   |   Terms & Conditions   |   Legal Statement

Copyright © 2013-2016 MOLBASE All Rights Reserved ICP Shanghai 14014220