Recommended Suppliersmore
Adipoyl chloride 111-50-2 MSDS
Name: Adipoyl chloride Material Safety Data Sheet
Synonym: Hexanedioyl Dichloride
CAS: 111-50-2
Section 1 - Chemical Product   MSDS Name:Adipoyl chloride Material Safety Data Sheet
Synonym:Hexanedioyl Dichloride

Section 2 - COMPOSITION, INFORMATION ON INGREDIENTS
CAS# Chemical Name content EINECS#
111-50-2 Adipoyl chloride 100 % 203-876-4
Hazard Symbols: C
Risk Phrases: 14 34

Section 3 - HAZARDS IDENTIFICATION
  EMERGENCY OVERVIEW
Reacts violently with water. Causes burns.Corrosive.Water-Reactive.
Potential Health Effects
Eye:
Causes eye burns. When substance becomes wet or comes in contact with moisture of the mucous membranes, it will cause irritation. May cause chemical conjunctivitis and corneal damage.
Skin:
Causes skin burns. Contact with skin causes irritation and possible burns, especially if the skin is wet or moist. May cause irritation and dermatitis. May cause cyanosis of the extremities. May cause skin rash (in milder cases), and cold and clammy skin with cyanosis or pale color.
Ingestion:
May cause severe and permanent damage to the digestive tract. Causes gastrointestinal tract burns. May cause perforation of the digestive tract. May cause systemic effects.
Inhalation:
Causes chemical burns to the respiratory tract. Inhalation may be fatal as a result of spasm, inflammation, edema of the larynx and bronchi, chemical pneumonitis and pulmonary edema. Aspiration may lead to pulmonary edema. May cause systemic effects. Inhalation at high concentrations may cause CNS depression and asphixiation.
Chronic:
Effects may be delayed.

Section 4 - FIRST AID MEASURES
  Eyes: Get medical aid immediately. Do NOT allow victim to rub or keep eyes closed. Extensive irrigation with water is required (at least 30 minutes).
Skin:
Get medical aid immediately. Immediately flush skin with plenty of soap and water for at least 15 minutes while removing contaminated clothing and shoes. Wash clothing before reuse. Destroy contaminated shoes. If water-reactive products are embedded in the skin, no water should be applied. The embedded products should be covered with a light oil.
Ingestion:
Do NOT induce vomiting. If victim is conscious and alert, give 2-4 cupfuls of milk or water. Never give anything by mouth to an unconscious person. Get medical aid immediately.
Inhalation:
Get medical aid immediately. Remove from exposure to fresh air immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Do NOT use mouth-to-mouth resuscitation. If breathing has ceased apply artificial respiration using oxygen and a suitable mechanical device such as a bag and a mask.
Notes to Physician:

Section 5 - FIRE FIGHTING MEASURES
  General Information:
As in any fire, wear a self-contained breathing apparatus in pressure-demand, MSHA/NIOSH (approved or equivalent), and full protective gear. During a fire, irritating and highly toxic gases may be generated by thermal decomposition or combustion. Water Reactive. Material will react with water and may release a flammable and/or toxic gas. Use water spray to keep fire-exposed containers cool. Combustible Liquid. May ignite or explode on contact with steam or moist air. Containers may explode when heated. Containers may explode when heated or if contaminated with water.
Extinguishing Media:
Use dry sand or earth to smother fire. Do NOT use water directly on fire. Use foam, dry chemical, or carbon dioxide. DO NOT USE WATER! Do NOT get water inside containers. Contact professional fire-fighters immediately. Cool containers with flooding quantities of water until well after fire is out.

Section 6 - ACCIDENTAL RELEASE MEASURES
  General Information: Use proper personal protective equipment as indicated in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth), then place in suitable container. Avoid runoff into storm sewers and ditches which lead to waterways. Clean up spills immediately, observing precautions in the Protective Equipment section. Remove all sources of ignition. Use a spark-proof tool. Provide ventilation. Do not expose spill to water. Do not get water inside containers.

Section 7 - HANDLING and STORAGE
  Handling:
Wash thoroughly after handling. Wash hands before eating. Use only in a well-ventilated area. Do not allow water to get into the container because of violent reaction. Do not breathe dust, vapor, mist, or gas. Do not get in eyes, on skin, or on clothing. Empty containers retain product residue, (liquid and/or vapor), and can be dangerous. Keep container tightly closed. Avoid contact with heat, sparks and flame. Do not allow contact with water. Discard contaminated shoes. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose empty containers to heat, sparks or open flames. Keep from contact with moist air and steam.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of ignition. Store in a tightly closed container. Store in a cool, dry, well-ventilated area away from incompatible substances. Corrosives area. Do not get water inside containers.

Section 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION
  Engineering Controls:
Use explosion-proof ventilation equipment. Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower. Use adequate general or local exhaust ventilation to keep airborne concentrations below the permissible exposure limits.
Personal Protective Equipment Eyes: Wear appropriate protective eyeglasses or chemical safety goggles as described by OSHA's eye and face protection regulations in 29 CFR 1910.133 or European Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin exposure.
Clothing:
Wear appropriate protective clothing to prevent skin exposure.
Respirators:
A respiratory protection program that meets OSHA's 29 CFR 1910.134 and ANSI Z88.2 requirements or European Standard EN 149 must be followed whenever workplace conditions warrant a respirator's use.

Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
 
Physical State: Liquid
Appearance: colorless to yellow
Odor: Pungent odor.
pH: Not available.
Vapor Pressure: 2 mm Hg @ 20 C
Viscosity: Not available.
Boiling Point: 105.0 - 107.0 deg C @ 2.00mm
Freezing/Melting Point: Not available.
Autoignition Temperature: Not available.
Flash Point: 72 deg C ( 161.60 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water: Reacts.
Specific Gravity/Density: 1.2600g/cm3
Molecular Formula: C6H8Cl2O2
Molecular Weight: 183.03

Section 10 - STABILITY AND REACTIVITY
  Chemical Stability:
Stable under normal temperatures and pressures. Combines vigorously or explosively with water.
Conditions to Avoid:
Incompatible materials, ignition sources, contact with water, excess heat, exposure to moist air or water.
Incompatibilities with Other Materials:
Strong oxidizing agents.
Hazardous Decomposition Products:
Hydrogen chloride, phosgene, carbon monoxide, irritating and toxic fumes and gases, carbon dioxide.
Hazardous Polymerization: Has not been reported.

Section 11 - TOXICOLOGICAL INFORMATION
  RTECS#:
CAS# 111-50-2 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
Adipoyl chloride - Not listed by ACGIH, IARC, NIOSH, NTP, or OSHA.
Other:
See actual entry in RTECS for complete information.

Section 12 - ECOLOGICAL INFORMATION
 

Section 13 - DISPOSAL CONSIDERATIONS
  Products which are considered hazardous for supply are classified as Special Waste and the disposal of such chemicals is covered by regulations which may vary according to location. Contact a specialist disposal company or the local waste regulator for advice. Empty containers must be decontaminated before returning for recycling.

Section 14 - TRANSPORT INFORMATION
 
IATA
Shipping Name: CORROSIVE LIQUID, NOS
Hazard Class: 8
UN Number: 1760
Packing Group: II
IMO
Shipping Name: CORROSIVE LIQUID, NOS
Hazard Class: 8
UN Number: 1760
Packing Group: II
RID/ADR
Shipping Name: CORROSIVE LIQUID, NOS
Dangerous Goods Code: 8(36B)
UN Number: 1760

Section 15 - REGULATORY INFORMATION
 
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: C
Risk Phrases:
R 14 Reacts violently with water.
R 34 Causes burns.
Safety Phrases:
S 24/25 Avoid contact with skin and eyes.
WGK (Water Danger/Protection)
CAS# 111-50-2: No information available.
United Kingdom Occupational Exposure Limits
Canada
CAS# 111-50-2 is listed on Canada's DSL List.
CAS# 111-50-2 is not listed on Canada's Ingredient Disclosure List.
Exposure Limits
US FEDERAL
TSCA
CAS# 111-50-2 is listed on the TSCA inventory.


SECTION 16 - ADDITIONAL INFORMATION
N/A

Home   |   Announcement   |   Partners   |   Business Cooperation   |   Suppliers   |   Products    |   About Us   |   Contact Us   |   Privacy Policy   |   Terms & Conditions   |   Legal Statement

Copyright © 2013-2016 MOLBASE All Rights Reserved ICP Shanghai 14014220